Summary

Most UK domestic properties have a single-phase 230V supply. Three-phase (400V) is standard for commercial and industrial premises, and is increasingly relevant to domestic properties as electric vehicle charging, heat pumps, and large-scale solar battery systems push demand beyond what single-phase connections can handle.

Understanding three-phase is important for electricians and electrical contractors working on EV installations, large domestic extensions, commercial fit-outs, and farm or agricultural properties. It's also relevant for any tradesperson who encounters a three-phase installation and needs to understand how it differs from single-phase in terms of earthing, neutral conductors, and protection devices.

In the UK, the DNO owns the incoming supply infrastructure up to and including the cut-out. The customer side begins at the meter terminals. Upgrading from single-phase to three-phase requires DNO agreement and works on their network — it is not something a customer or their electrician can arrange unilaterally.

Key Facts

  • Single-phase supply — 230V L-N; standard UK domestic cut-out rated 60A or 100A (13.8kW or 23kW)
  • Three-phase supply — 400V between phases (L1-L2, L2-L3, L1-L3); 230V phase-to-neutral
  • Three-phase power calculation — P = √3 × VLL × I × PF (for balanced 3-phase load)
  • 100A three-phase supply — approximately 69kW at unity power factor (√3 × 400 × 100)
  • DNO (Distribution Network Operator) — owns the supply network to the cut-out; different by region (National Grid Electricity Distribution, SP Energy Networks, UK Power Networks, etc.)
  • G99 connection application — required for generation > 3.68kW per phase; applies to solar PV and battery systems
  • Balanced loading — loads should be distributed evenly across phases to prevent neutral current and maintain supply quality
  • Three-phase consumer unit — requires 3-pole or 1-pole MCBs on each phase; neutral size matched to phase conductors unless neutral is de-rated for balanced loads
  • TN-C-S (PME) three-phase — most common in UK three-phase domestic/light commercial supply; PEN conductor from transformer
  • Phase sequence — L1-L2-L3 (positive sequence RYB or UVW); important for motor direction and phase-sequence relays
  • Three-phase motors — rotate in direction determined by phase sequence; swap any two phases to reverse rotation
  • Harmonic distortion — non-linear loads (inverters, variable speed drives) create harmonic currents that can overheat the neutral even with balanced fundamental loads

Quick Reference Table

Quoting an electrical job? Describe the work and squote handles the pricing.

Try squote free →
Scenario Single Phase Sufficient? Three Phase Required?
Standard domestic (up to 23kW) Yes No
Single EV charger (7kW) Yes No
Multiple EV chargers (3 × 7kW) Marginal Preferred
Air source heat pump (up to 5kW input) Yes No
Large heat pump system (8kW+ input) Marginal Often preferred
Large electric range/Aga (up to 13kW) Yes with 60A supply No
Large Aga or commercial range (>20kW) No Yes
Workshop/small commercial Depends on load Often required
Agricultural premises Usually no Often required
Voltage Measurement Value
Phase-to-neutral (L-N) 230V
Phase-to-phase (L-L) 400V
Phase-to-phase formula 230 × √3 = 400V
Three-phase power (balanced) √3 × 400 × I

Detailed Guidance

When Three-Phase Is Needed

The key question is whether the total connected load (with appropriate diversity) exceeds single-phase capacity. A 100A single-phase supply can deliver:

  • Maximum 23kW (100A × 230V = 23,000W)
  • In practice, after diversity, typical domestic load rarely exceeds 15–18kW on a 100A cut-out

Three-phase becomes appropriate when:

  1. Multiple large loads operate simultaneously. Two EV chargers at 7.4kW each = 14.8kW. Add a heat pump compressor at 4kW, electric hob at 6kW, and you're at 24.8kW before the rest of the house — single phase inadequate.
  2. Large motor loads are installed. Some large compressors and industrial equipment are only available in three-phase versions.
  3. The DNO cannot supply sufficient single-phase capacity. In areas with weak single-phase networks, the DNO may offer three-phase more readily as it spreads load across the network.
  4. Commercial or agricultural premises. Workshop equipment, commercial refrigeration, commercial catering equipment.

DNO Upgrade Process

The application process varies by DNO but typically follows this sequence:

  1. Assess demand — calculate total connected load, apply diversity, determine required supply rating (amps per phase)
  2. Apply to DNO — the property owner (not the electrician) applies through the DNO's connection service portal or by phone. Some DNOs have forms; UK Power Networks has an online process.
  3. DNO assessment — DNO checks local network capacity to supply three-phase. Network reinforcement may be needed.
  4. Quotation — DNO provides a cost for connection works. This can range from £1,500 for a simple upgrade (existing three-phase cable in street) to £20,000+ if network reinforcement required.
  5. Customer acceptance and payment — customer pays and confirms acceptance
  6. Works programme — DNO schedules cable laying, service upgrade, meter installation. Can take weeks to months.
  7. Internal works — customer's electrician installs new three-phase consumer unit and upgrades internal wiring ahead of or concurrent with DNO works.
  8. Energisation — DNO energises new supply.

The customer's electrician does not touch the DNO's equipment — the cut-out and supply cable are DNO property. The electrician prepares the internal tails and meter board position.

Three-Phase Consumer Units and Distribution Boards

A three-phase installation requires:

  • Three-phase main switch (3-pole or 4-pole with neutral)
  • MCBs or RCBOs on each phase (single-pole protection acceptable for most final circuits)
  • Main incoming supply of four conductors: L1, L2, L3, N (plus earth)
  • Three-phase submains use 4-core SWA or XLPE cable

Load balancing:

  • Distribute loads across phases: e.g., ring finals on L1, L2, L3 in rotation
  • Three-phase loads (motors, large cookers) connected across all three phases via 3-pole MCB
  • Large single-phase loads should be balanced: EV charger on L1, heat pump on L2, rest of house on L3

Earthing on Three-Phase Installations

Earthing principles are the same as single-phase but scaled up:

  • Main earthing terminal (MET) connects supply earth to installation earth
  • Main bonding conductors: minimum 10mm² for PME three-phase supply (same as single-phase PME)
  • CPC sizing as per Regulation 543 (adiabatic equation; minimum 16mm² for large submains)
  • Earth fault loop impedance limits same per-circuit regardless of three-phase supply

TT systems with three-phase supplies require an earth electrode capable of handling fault currents from any phase.

Three-Phase for EV Charging

Three-phase EV chargers offer 22kW charging rate (32A per phase × 400V × √3 = 22kW). Vehicle must support three-phase on-board charger — only some vehicles have three-phase chargers (primarily newer Zoe models, some commercial vans). Most EVs still have single-phase on-board chargers (maximum 7.4kW) even when connected to a three-phase supply.

For domestic EV installation, three-phase provides future flexibility even if current vehicles don't use it. G99 application is not required for EV chargers alone.

Frequently Asked Questions

Can I install three-phase cable internally before the DNO provides the supply?

Yes. The electrician can install the internal three-phase consumer unit, distribution board, and internal wiring in advance. The DNO supply cable is connected at the point of energisation. Ensure the internal tails are accessible at the meter position and the main switch is rated for the agreed supply capacity.

Do I need a three-phase meter?

Yes — the DNO will fit a three-phase smart meter (SMETS2). Each phase is metered separately. Tariffs are typically the same as single-phase. Smart meters enable half-hourly meter reading and compatibility with time-of-use tariffs.

What happens if phases are not balanced?

Unbalanced loading causes a neutral current (the difference between phase currents flows in the neutral). This neutral current can cause:

  • Voltage variation between phases (those with more load have lower voltage)
  • Overheating of undersized neutral conductors
  • Interference with sensitive equipment

Aim to balance loads to within 20% of each other across phases.

Regulations & Standards

  • BS 7671:2018+A2:2022 — 18th Edition Wiring Regulations; three-phase requirements throughout, particularly Chapter 41 (ADS) and Chapter 54 (earthing)

  • G99 — Requirements for the Connection of Generation Equipment in Parallel with Public Distribution Networks (Energy Networks Association) — applies to solar/battery systems

  • The Electricity Safety, Quality and Continuity Regulations 2002 (as amended) — DNO connection standards

  • BS EN 60309 — Industrial plugs and socket outlets (for 3-phase socket installations)

  • IET Guidance Note 8 — Wiring Regulations: Earthing

  • UK Power Networks New Connections — DNO connection portal

  • National Grid Electricity Distribution New Connections — Midlands and South West DNO

  • Energy Networks Association ENA G99 — Generation connection requirements

  • IET Wiring Regulations — BS 7671:2018+A2:2022

  • earthing bonding — Earthing for three-phase installations

  • ev charger — EV charger installation and DNO notifications

  • consumer units — Consumer unit selection including three-phase units

  • testing commissioning — Testing three-phase installations